Baileigh Metal Cutting Band Saw Machines

BS-210M Single Miter 110 Volt - Horizontal BandSaw

Miter cuts up to sixty degrees. Uses 110 volts electricity.
Two cutting functions (Manual or Controlled Descent).
Good for small machine shops where metal sawing applications under 6-3/4" round or square. Like other Baileigh bandsaws, it comes standard with the ability to manually cut using a trigger switch and handle, or it can be switched over to utilize a hydraulically controlled descent feature normally seen on more expensive models. The hydraulic descent feature controls the descent pressure for perfect cuts so can walk away from the machine since it will automatically stop the blade once the metal is finished being cut. A powerful 1-1/2 HP DC motor has the proper torque to drive the direct drive gearbox with no chatter, even at slower cutting speeds that are required when cutting the likes of mild steel. This machine comes standard with a DC variable speed drive allowing the operator to use the proper speed when cutting different materials like mild steel or aluminum, that increases blade life and cutting speed. The mitre angle takes seconds to change for increased production in any fabrication or machine shop and offers tooless changeovers. The vise has a rapid advancing handwheel and the vise is locked by a 1/4 turn taper handle that holds the material very secure against the searated vise plates to further reduce slipage. Such a vise system increases blade life especially when cutting round material like tubing or pipe. This horizontal band saw has a comfortable working vise height of 35 inches off the floor which reduces operator back fatigue when lifting.
The saw has a powerful industrial grade coolant pump that lubricates the blade, cools the teeth and blasts away cut chips that extends blade life. A precise liquid filled blade tension gauge extends blade and bearing life offering decades of precision sawing. Designed with a nice solid cast iron sawing head allowing for straighter cuts than welded frames. Our band saws have quality Koya taper bearings connected to hardened and ground drive shafts offering further rigidity. The blade guides employ a hardened roller bearing 1/4 turn device to straighten out the blade that is further held securely in Tungston carbide guides, assuring very straight and accurate cuts. Blade tensioning.

Click to Request this Quote

General Specifications:
Blade Size:.78" x .035" x 83 Blade Speed: 114 to 262 fpm
Motor: 1.5 HP, 110 volts 1 ph
Measurements: 45.5"x22.5"x32.5" (W x L x H)
Weight: 344 Lbs.

BS-250M Single Miter 110 Volt - Horizontal Band Saw

Capable of cutting up to 9 inch round metal stock. This mitering bandsaw can cut from zero up to sixty degree angles. It has a powerful 2 HP DC motor that delivers high torque even at slower speeds, ensuring no chattering of the blade, extending blade life. This horizontal metal cutting band saw has a direct drive gear box, meaning there are no pulleys or belts, so your blade will last longer with such a positive drive. The BS-250M has a DC variable speed drive for speeds from 114 to 262 feet per minute allowing the operator to precisely adjust the speed for the proper blade and material, again increasing the life of the blade and decreasing cutting rates. Like all Baileigh bandsaws this one includes a powerful industrial grade coolant pump that washes away chips before and after the cutting area. This cools the blade teeth, lubricates the blade, and removes the metal chips from the blade. The BS-250 band saw cuts using the pull down arm and trigger switch to activate the blade and coolant, or if your in more of a production run, you can switch the machine over to cut metal using the hydraulic descent feature that will cut through the metal using the pressure you determine and will shut down the blade and coolant when completed. To change the mitre angle takes seconds considering the change uses no tools and there are no alterations needed to the vise position. The BS-250 comes standard with a stop gauge in inches and milimeters. The vise can quickly be positioned via hand wheel and ulitmately locked into position on the piece of material using a 1/4 turn taper lock coupled to the searated clamps to assure no movement to the material being cut, this ultimatly will increase blade life. The cabinet allows for a back friendly height of 35 inches and uses as little floor space as possible. Best of all this horizontal band saw requires a 110 volts of power, meaning it can work in any facility in North America that has power. Perfect for small to large metal cutting machine shops and metal fabricating shops.
Includes Blade Tension Device.
Two cutting functions (Manual or Controlled Descent)

Click to Request this Quote

General Specifications:
Blade Size: 1" x .035" x 96"
Blade Speed: 114 to 262 fpm
Motor: 2 HP, 110 volts 1 ph
Machine size: 61" x 29" x 36"H
Weight: 475 Lbs.

BS-260M Dual Miter BandSaws

Extra wide blade! Cast iron saw head provides rigidity and swivels in two directions (dual mitering), 0-60 degrees (R) and 0-45 degrees (L) Direct gear drive helps extend saw blade life, and allows saw head to make more accurate cuts and cut faster. Dual descent modes: 1 -Manual descent mode is operated by pulling down on handle and actuating trigger switch. 2- Hydraulic descent feed can be adjusted by operator. Powerful coolant pump cools blade, assists chip removal system, and extends blade life. We recommend using an petroleum based or synthetic based coolant that you would typically mix with a 1 to 10 ratio (coolant to water). This type of coolant can be purchased at any local industrial supplier. Broken blade tension devise shuts down machine if blade breaks. The gear driven BS-260M is a 9" Band Saw and is the perfect saw for cutting at 90 degrees or miter angles. This saw has a dual angle head capable of cutting 0-60 degrees (R) and 0-45 (L), making it one of the most versatile saws on the market. Quick releases allow the operator to change the miter angle in seconds. Each gear driven metal cutting band saw we offer has variable speed, miter heads, and a hydraulic controlled descent devise for perfect feeds and longer blade life. This machine ships with a quality blade that is 97" long. It is recommened that you use quality saw blades purchased by reputable manufacturers like Lenox®, Starrett® or Wikus®. Our band saws are constructed of a heavy cast iron saw head and base and the blades are guided via a tungsten carbide insert offering rigidity and accuracy. Each band saw has a powerful coolant system and a broken blade tensioning devise that shuts down the machine if the blade breaks. This is the perfect bandsaw for cutting solids, tube or pipe, angle iron and much more. These mitering saws are great for cutting ferrous and non-ferrous metals such as aluminum, mild steel, stainless steel, chromoly or brass. This series of bandsaw offers two cutting functions: 1- Manual descent for small production runs. The operator simply turns on the machine via a trigger switch in the descent handle, and manually guides the band saw blade through the material. Perfect for the small or medium sized fabricators needs. 2- Hydraulic descent for larger production runs increases blade life and reduces operator fatigue. The hydraulic descent has a down feed adjustment for feed pressure. The saw head is manually lifted to reset the hydraulic descent for the next cut. This metal bandsaw can cut up to 8" x 9-1/2" rectangle. This model has service requirements of 220V, Single Phase, 60 Hertz. This horizontal bandsaw has a dual swiveling miter head, allowing the operator to miter 60 degrees in one direction and 45 degrees in the other direction. The vise is fitted with a quick release and tightening feature that allows for very quick operator cycle times between cuts. The vise has quick change over features when changing cut angles.This series of horizontal band saw comes standard with a DC variable speed drive allowing the operator to fine tune the blade speed from 114' to 262 feet per minute. The DC drive also allows for high torque when cutting at slower speeds, which increases blade life. This metal cutting saw series requires a 1" wide saw blade by .035" wall thickness, making this series a very precise miter saw.
Blade tension device shuts down machine if blade breaks. Two cutting functions (manual or controlled descent)

Click to Request this Quote

General Specifications:
Blade Size:1.63 x .035 x 96.9"
Blade Speed: 114 to 262 fpm
Motor: 2 HP, 110 volts 1 ph
Machine size: 61" x 29" x 42"H
Weight: 620 Lbs.

BS-260SA Dual Miter Semi-Auto Band Saws

Semi- Automatic down feed and up feed Hydraulic clamping vise Cast iron saw head provides rigidity and swivels in two directions, 0-60 degrees (R) and 0-45 degrees (L) Direct gear drive helps extend saw blade life, and allows saw head to make more accurate cuts and cut faster.. Powerful coolant pump cools blade and assists chip removal system Broken blade tension devise shuts down machine if blade breaks. The gear driven BS-260SA is a 9" dual miter Band Saw and is the perfect saw for cutting at 90 degrees or miter angles. This saw has a dual angle head capable of cutting 0-60 degrees (R) and 0-45 (L), making it one of the most versatile saws on the market. Quick releases allow the operator to change the miter angle in seconds. The vise clamp uses a handwheel coupled to a low ratio acme screw for positioning and a quick release and load hydraulic clamping system. Each semi-automatic gear driven metal cutting band saw we offer has variable speed, miter heads, hydraulic vise, and semi automatic downfeed and up feed for perfect feeds and longer blade life. Our band saws are constructed of a heavy cast iron saw head and base and the blades are guided via a tungsten carbide insert offering rigidity and accuracy. Each band saw has a powerful coolant system and a broken blade tensioning devise that shuts down the machine if the blade breaks. The hydraulic descent has a down feed adjustment for feed pressure. The saw head is automatically lifted when the cut is complete and is ready for the next cut. This metal bandsaw can cut up to 8" x 9-1/2" rectangle. These models have service requirements of 220V, Single Phase, 60 Hertz. The BS-260-SA horizontal bandsaw has a dual swiveling miter head, allowing the operator to miter 60 degrees in one direction and 45 degrees in the other direction. This series of horizontal band saw comes standard with a variable speed drive allowing the operator to fine tune the blade speed from 114' to 262 feet per minute. The SA metal cutting saw series requires a 1" wide saw blade by .035" wall thickness, making this series a very precise semi-automatic miter saw.

Blade tension device shuts down machine if blade breaks.
Semi Automatic Cutting Function with hydraulic vise.

Click to Request this Quote

General Specifications:
Blade Size:1.63 x .035 x 96.9"
Blade Speed: 114 to 262 fpm
Motor: 2 HP, 220 volts 1 ph
Machine size: 61" x 29" x 42"H
Weight: 620 Lbs.

BS-350M Dual Miter BandSaws

Cast iron saw head provides rigidity and swivels in two directions, 0-60 degrees (R) and 0-45 degrees (L) Direct gear drive helps extend saw blade life, and allows saw head to make more accurate cuts and cut faster. Dual descent modes: 1 -Manual descent mode is operated by pulling down on handle and actuating trigger switch. 2- Hydraulic descent feed can be adjusted by operator. Powerful coolant pump cools blade and assists chip removal system. We recommend using a petroleum or synthetic based coolant mixture that is typically mixed with water in a 1:10 ratio. Broken blade tension devise shuts down machine if blade breaks. The gear driven BS-350M is a 10-1/2" dual miter Band Saw and is the perfect saw for cutting at 90 degrees or miter angles. This saw has a dual angle head capable of cutting 0-60 degrees (R) and 0-45 (L), making it one of the most versatile bandsaws on the market. Quick releases allow the operator to change the miter angle in seconds. The vise also has a handwheel for tightening and is coupled with a quick release and load torque handle for tightening and loosing metal bars in seconds. Each gear driven metal cutting bandsaw we offer has variable speed, miter heads, and a hydraulic controlled descent devise for perfect feeds and longer blade life. Our bandsaws have DC variable speed drives that offers consistent torque even at slower speeds, which increases blade life. Our band saws are constructed of a heavy cast iron saw head and base and the blades are guided via a tungsten carbide insert offering rigidity and accuracy. Each band saw has a powerful coolant system and a broken blade tensioning devise that shuts down the machine if the blade breaks. This machine is perfect for cutting solid bar stock, as well as tubing and pipe. Metal cut easily on the BS-350M include mild and stainless steel, aluminum, chromoly and bronze. Plastics of many different sorts can be cut on this machine as well. The BS-350M series bandsaw offers two cutting functions: 1- Manual descent for small production runs. The operator simply turns on the machine via a trigger switch in the descent handle, and manually guides the band saw blade through the material. Perfect for the small fabricators needs. 2- Hydraulic descent for larger production runs increases blade life and reduces operator fatigue. The hydraulic descent has a down feed adjustment for feed pressure. The saw head is manually lifted to reset the hydraulic descent for the next cut. This metal band saw can cut up to 8-1/2"x13-3/4" rectangle. This model has service requirements of 220V, Single Phase, 60 Hertz. The BS-350M horizontal bandsaw has a dual swiveling miter head, allowing the operator to miter 60 degrees in one direction and 45 degrees in the other direction. This series of horizontal band saw comes standard with a variable speed drive allowing the operator to fine tune the blade speed from 114' to 262 feet per minute. The BS-350M metal cutting saw requires a 1" wide saw blade by .035" wall thickness that is 125" long, making this series a very precise miter saw.
Blade tension device shuts down machine if blade breaks.
Two cutting functions (manual or controlled descent)

Click to Request this Quote

General Specifications:
Blade Size:.984"x.035x124.4"
Blade Speed: 114 to 262 fpm
Motor: 2 HP, 220 volts 1 ph
Machine size: 74"x 30"x 44"H
Weight: 800 Lbs.

BS-350SA Dual Miter BandSaw

Semi- Automatic down feed and up feed Hydraulic clamping vise Cast iron saw head provides rigidity and swivels in two directions, 0-60 degrees (R) and 0-45 degrees (L) Direct gear drive helps extend saw blade life, and allows saw head to make more accurate cuts and cut faster. Dual descent modes: 1 -Manual descent mode is operated by pulling down on handle and actuating trigger switch. 2- Hydraulic descent feed can be adjusted by operator. Powerful coolant pump cools blade and assists chip removal system. We recommend using a petroleum or synthetic based coolant mixture that is typically mixed with water in a 1:10 ratio. Broken blade tension devise shuts down machine if blade breaks. The gear driven BS-350SA is a 10-1/2" dual miter Semi Automatic Band Saw and is the perfect saw for cutting at 90 degrees or miter angles. This saw has a dual angle head capable of cutting 0-60 degrees (R) and 0-45 (L), making it one of the most versatile bandsaws on the market. Quick releases allow the operator to change the miter angle in seconds. The vise clamp uses a handwheel coupled to a low ratio acme screw for positioning and a quick release and load hydraulic clamping system. Each gear driven semi automatic metal cutting bandsaw we offer has variable speed, miter heads, and a hydraulic controlled descent devise for perfect feeds and longer blade life. Our bandsaws have DC variable speed drives that offers consistent torque even at slower speeds, which increases blade life. Our band saws are constructed of a heavy cast iron saw head and base and the blades are guided via a tungsten carbide insert offering rigidity and accuracy. Each band saw has a powerful coolant system and a broken blade tensioning devise that shuts down the machine if the blade breaks. This machine is perfect for cutting solid bar stock, as well as tubing and pipe. Metal cut easily on the BS-350SA include mild and stainless steel, aluminum, chromoly and bronze. Plastics of many different sorts can be cut on this machine as well. The BS-350SA series bandsaws hydraulic descent has a down feed adjustment for feed pressure. The saw head is automatically lifted when the cut is complete and is ready for the next cut. The hydraulic descent has a down feed adjustment for feed pressure. This metal band saw can cut up to 8-1/2"x13-3/4" rectangle. This model has service requirements of 220V, Single Phase, 60 Hertz. The BS-350SA horizontal bandsaw has a dual swiveling miter head, allowing the operator to miter 60 degrees in one direction and 45 degrees in the other direction. This series of horizontal band saw comes standard with a variable speed drive allowing the operator to fine tune the blade speed from 114 to 262 feet per minute. The BS-350SA metal cutting saw requires a 1" wide saw blade by .035" wall thickness that is 125" long, making this series a very precise miter saw.
Blade tension device shuts down machine if blade breaks.
Semi Automatic Cutting Function with hydraulic vise.

Click to Request this Quote

General Specifications:
Blade Size:.984"x.035x124.4"
Blade Speed: 114 to 262 fpm
Motor: 2 HP, 220 volts 1 ph
Machine size: 74"x 30"x 44"H
Weight: 1010 Lbs.

BS-330M Single Miter Band Saw

The BS-330M band saw uses a 1-1/4" band saw blade, making it an extremely accurate and fast cutting saw. Saw head provides rigidity and swivels 0-45 degrees. Direct gear drive helps extend saw blade life, and allows saw head to make more accurate cuts and cut faster. Hydraulic descent feed can be adjusted by operator. Powerful coolant pump cools blade and assists chip removal system. Broken blade tension devise shuts down machine if blade breaks. The BS-330M is a metal cutting band saw capable of cutting 13" OD and is the perfect saw for cutting at 90 degrees or single miter angles. This saw can cut up to 13" x 18½" material, meaning you get more value for your investment than with any other saw on the market. Quick releases allow the operator to change the miter angle in seconds. Each gear driven metal cutting bandsaw we offer has variable speed, miter heads, and a hydraulic controlled descent devise for perfect feeds and longer blade life. Our band saws are constructed of a heavy cast iron saw head and base and the blades are guided via a tungsten carbide insert offering rigidity and accuracy. Each band saw has a powerful coolant system and a broken blade tensioning devise that shuts down the machine if the blade breaks. The BS-330M metal band saw has a hydraulic descent for larger production runs that increases blade life and reduces operator fatigue. It has a hydraulic descent control device for the down feed, that is reset when the head is manually lifted. This metal bandsaw series can cut up to 13" OD capacities. This series of band saw requires 220V, Three Phase, 60 Hertz. The BS-330M horizontal bandsaw has a miter saw head that can cut from 90 to 45 degrees. This series of horizontal band saw comes standard with a variable speed drive allowing the operator to fine tune the blade speed from 114' to 262 feet per minute. The BS-330M metal cutting saw series requires a 1-1/4" wide saw blade by .042" wall thickness, making this series a very precise miter saw.

Click to Request this Quote

General Specifications:
Blade Size:1.33"x.042x161.5"
Blade Speed: 114 to 262 fpm
Motor: 3 HP, 220 volts 3 ph
Machine size: 90"x 38"x 58"H
Weight: 1650 Lbs.

BS-330SA Single Miter Semi-Auto Bandsaw

Semi- Automatic down feed and up feed Hydraulic clamping vise The BS-330SA band saw uses a 1-1/4" band saw blade, making it an extremely accurate and fast cutting saw. Saw head provides rigidity and swivels 0-45 degrees. Direct gear drive helps extend saw blade life, and allows saw head to make more accurate cuts and cut faster. Hydraulic descent feed can be adjusted by operator. Powerful coolant pump cools blade and assists chip removal system. Broken blade tension devise shuts down machine if blade breaks. The BS-330SA is a metal cutting band saw capable of cutting 13" OD and is the perfect semi automatic band saw for cutting at 90 degrees or single miter angles. This saw can cut up to 13" x 18½" material, meaning you get more value for your investment than with any other saw on the market. Quick releases allow the operator to change the miter angle in seconds. Each gear driven metal cutting bandsaw we offer has variable speed, miter heads, and a hydraulic controlled descent devise for perfect feeds and longer blade life. The vise uses a hydraulic clamping system and after the cut is complete the blade stops, the vise opens and the head lifts to the start position for the next piece to be cut. Our band saws are constructed of a heavy cast iron saw head and base and the blades are guided via a tungsten carbide insert offering rigidity and accuracy. Each band saw has a powerful coolant system and a broken blade tensioning devise that shuts down the machine if the blade breaks. The BS-330SA metal band saw has a hydraulic descent for larger production runs that increases blade life and reduces operator fatigue. It has a hydraulic descent control device for the down feed, that is reset when the head is automatically lifted. This metal bandsaw series can cut up to 13" OD capacities. This series of band saw requires 220V, Three Phase, 60 Hertz. The BS-330SA semi automatic horizontal bandsaw has a miter saw head that can cut from 90 to 45 degrees. This series of horizontal band saw comes standard with a variable speed drive allowing the operator to fine tune the blade speed from 114' to 262 feet per minute. The BS-330SA metal cutting saw series requires a 1-1/4" wide saw blade by .042" wall thickness, making this series a very precise miter saw. These band saws offer more cutting capacity in a variable speed miter saw.

Click to Request this Quote

General Specifications:
Blade Size:1.33"x.042x161.5"
Blade Speed: 114 to 262 fpm
Motor: 3 HP, 220 volts 3 ph
Machine size: 90"x 38"x 58"H
Weight: 1650 Lbs.

BS-20M Single Miter Horizontal Band Saw

The BS-20M 13" x 18" single miter Manual Band Saw has a 13'6" L x 1" x .032" thick blade. The BS-20M has extremely heavy-duty cast iron guide arms and wheels. This saw has a great working height of 31" and has a pre-loading and post cutting table that holds the infeed bar and the cut piece, allowing for straighter cuts and longer blade life. The BS-20M band saw uses a 1" band saw blade, making it an extremely accurate and fast cutting saw. Blades for this model can be sourced at your local industrial distributor. We recommend using good quality blades manufactured by Lenox®, Starrett®, or Wikus®. The heavy cast iron saw head provides rigidity and swivels 0-60 degrees. Direct gear drive helps extend saw blade life, and allows saw head to make more accurate cuts and cut faster. Hydraulic descent feed or pressure can be adjusted by operator. This is important when cutting different size and different types of material. Powerful coolant pump cools blade and assists chip removal system. We recommend a petroleum based or synthetic based coolant that should be mixed 1:10 (coolant to water). These coolants can be sourced at your local industrial distributor. A broken blade tension devise shuts down the machine incase a blade breaks. This is the perfect machine for cutting solids (round, square, or rectangles), tubing, angle iron and much more in angles up to 60 degrees. Perfect for the small to medium fabricator or job shop who needs to cut mild steel, stainless steel, aluminum, chromoly, brass, bronze, and even plastics. Fitted with the proper blade, this machine will provide years of profitable production. The BS-20M is a Band Saw capable of cutting 13" OD and is the perfect saw for cutting at 90 degrees or miter angles. This saw can cut up to 13" x 18" material, meaning you get more value for your investment than with any other saw on the market. Quick releases allow the operator to change the miter angle in seconds. This band saw has four operating speeds, a miter head, and a hydraulic controlled descent devise for perfect feeds and longer blade life. Our band saws are constructed of a heavy cast iron saw head and base and the blades are guided via a tight tolerance hardened roller bearings and accompanied by tungsten wear guides. Each band saw has a powerful coolant system and a broken blade tensioning devise that shuts down the machine if the blade breaks. Of course guard doors are interlocked, so if someone opens a guard while the machine is running it will shut down the saw. The BS-20 series band saw has a hydraulic descent for larger production runs that increases blade life and reduces operator fatigue. It has a hydraulic descent control device for the down feed, that is reset when the head is manually lifted. This metal bandsaw series can cut up to 13" OD capacities. The BS-20 horizontal bandsaw has a miter saw head that can swivel up up to 60 degrees. 4 drive speeds allow the operator to fine tune the blade speed for the material they are cutting. The BS-20 metal cutting saw series requires a 1" wide saw blade by .032" wall thickness, making this series a very precise miter saw. These band saws offer more cutting capacity in a variable speed miter saw.
Manual Vise.

Click to Request this Quote

General Specifications:
Blade Size:1.06x.035x162.6"
Blade Speeds:
90, 140, 220, or 330 fpm
Motor: 3 HP, 220 volts 3 ph
Machine size: 81"x 70"x 57"H
Table Height: 31"
Weight: 1800 Lbs.
Coolant Tank: 6 gallons

BS-20SA Single Miter Semi-Auto Bandsaw

The BS-20SA semi-automatic bandsaw offers a great floor plan with a heavy duty infeed table and out feed table. This band saw can be adjusted to miter from zero degrees to 60 degrees in seconds by simply lifting the lock down mechanism, there is no adjustment required to the vise clamping area. The saw cutting head swivels, while the vise and base stay stationary. The BS-20SA horizontal band saw requires a 1" band saw blade, making it an extremely accurate and fast cutting saw. Blades for this model can be sourced from your local industrial distributor. We recommend good quality replacement blades manufactured by Lenox®, Starrett®, or Wikus®. Semi automatic bandsaws like the BS-20SA hydraulically clamp the metal prior to the saw head that hydraulically descents when cutting through the material. After the cut is complete the blade stops and the head is hydraulically lifted, and the vise opens awaiting the next cut. This horizontal band saw comes standard with a variable speed drive. This allows the user to fine tune the proper speed for different materials like mild steel, bronze or aluminum. The hydraulic descent pressure can be adjusted by the operator achieving faster cut times and longer blade life, depending on what material the operator is cutting. The return position of the metal cutting head can be altered to achieve faster cycle times between cuts, when cutting smaller dimensioned pieces. This machine has an industrial grade wet coolant system with powerful streams before and after the piece of metal being cut. A powerful blast of synthetic coolant cools the blade teeth for the next cut, lubricates the blade, and blasts away metal chips that all contribute to longer blade life and a straighter cut. A typical synthetic cutting coolant comes in a five gallon container and usually requires a 1 to 10 mixture with water, meaning you can produce up to 50 gallons from one five gallon container. This coolant can be purchased locally at any industrial distributor. All Baileigh band saws come with a precise liquid filled blade tension gauge that allows for perfect tensions every time. This drastically improves blade and bearing life. The BS-20SA has a maximum cutting capacity of 13 x 18 inches. It is perfect for cutting tubing, angle iron or solids like steel or aluminum at mitre angles or perfect 90 degree cuts. The best thing about this semi automatic bandsaw is how user friendly it is for the operator. The design has slowly evolved over the past twenty years into this perfect metal cutting machine that allows miter angle changes to happen in seconds instead of minutes with older designs. The heavy duty roller table before the blade makes advancing heavy pieces of metal a breeze. The discharge table after the blade has a drop height of 1/8 inch that decreases blade twist and tooth damage increasing increasing blade life. The clamping area of this industrial bandsaw has a searated plate and powerful hydraulic clamp that ensures there won't be any movement of the metal to be cut, this decreases blade damage.

Click to Request this Quote

General Specifications:
Blade Size:1.06x.035x162.6"
Blade Speeds:
90, 140, 220, or 330 fpm
Motor: 3 HP, 220 volts 3 ph
Machine size: 81"x 70"x 57"H
Table Height: 31"
Weight: 2200 Lbs.
Coolant Tank: 6 gallons